prismaequipamentos

CAPACIMETRO DIGITAL VICTOR MODELO 6013C NOVO " PROMOÇAO"

Capacitance Ohmmeter
Ⅰ. General
Equipped with the 33mm text height LCD display of clear reading and visual display, is a 3 5/6 digital multi-meter which has the merits of intelligence, stable performance, high reliability and convenient operation. It could be used to measure resistance, capacity and diode and make on-and-off test. Meanwhile, it is available for unit symbol display, data retention, the measurement of maximum and minimum value, automatic/manual range switching, automatic power off, automatic identification and alarm function. The complete machine takes a switching integrated circuit which can directly drive LCD microprocessor and double-integrating A/D and a digital display drive offering high resolution and high precision. Due to its complete functions, high measurement accuracy and convenient operation, the multi-meter is the ideal tool in laboratory and factory as well as for radio fans and family.
Ⅱ. Open-package Inspection
Open the package box and take out the meter, check carefully if the following accessories are absent or damaged. If there is any absence or damage, please contact the distributor immediately.
Digital Multi-meter 1 PC Instruction Manual 1 copy
Test leads 1 pair 1.5V AAA battery 1 pair
Holster 1 PC
Ⅲ. Safety Considerations
In order to avoid endangering the operator’s safety, prior to the operation of the instrument, please read the instruction manual carefully, and conform to the safety warning information and operation instruction strictly to use the instrument.
1. When voltage above 30V, current above 10mA, AC power line with inductive load or power line during electric fluctuation is measured, please beware of electric shock.
2. Prior to measurement, check if the measurement function is in conformity with the LCD display, and if the pushbutton switch is at the trigger position. Check if the meter pen is contacted reliably, connected correctly, and grounded well and etc. in order to avoid electric shock.
3. Only if the meter is used with the matched meter, can it meet the requirement of safety standard. When the line of the meter pen is damaged, it is necessary to replace another one of the same model or the same electrical specification.
4. Don’t use other unconfirmed or disapproved protector tube to replace the protector tube inside the meter. Only the protector tube of the same model or same specification can be replaced. Before the replacement, the test leads must leave the measuring point and ensure there is no any signal at the input terminal.
5. Don’t use other unconfirmed or disapproved battery to replace the battery inside the meter. Only the battery of the same model or same electrical specification can be replaced. Before the replacement, the meter must leave the measuring point and ensure there is no any signal at the input terminal.
6. When the electrical measurement is made, never let your body get in touch with the ground directly, and don’t touch uncovered metal terminal, output port, lead clamp and etc. where earth potential may exist. Dry clothes, rubber shoes, rubber cushion and other insulating material are usually used to keep your body insulated against the ground.
7. Don’t store and use it in the high-temperature, high-humidity, inflammable and strong magnetic field environment.
8. It may do damage to the meter and endanger the operator’s safety if the voltage value beyond the permitted ultimate voltage value is measured. The ultimate voltage value permitted for measurement is marked on the instrument panel, and never measure the value exceeding the standard. Don’t input the ultimate value out of regulation in order to avoid electric shock and the damage to the meter.
9. When the meter is inserted into the current socket, don’t measure any voltage for fear that the meter should be damaged and the operator’s safety be endangered.
10. Don’t try calibrating or repairing the meter. When it is indeed necessary for that, only the qualified professional personnel who have had special training or gained approval can make it.
11. During measurement, the requirement of measurement function must be in accordance with LCD display. Please be sure to disconnect the line of the meter pen with the measured object first and ensure there is no any input signal. It is forbidden to switch the function/range selection switch during measurement
12. When “ ”is shown on LCD display, please replace battery immediately to ensure the measurement precision.
13. It is not allowed to insert the meter into the current terminal to measure voltage!
14. Please don’t change the circuits of the meter freely for fear that the meter be damaged and the safety be endangered.
15. Description of Safety Symbols
Warning! In accordance with the instructions of European Trade Union
High Voltage! Danger! Double Insulation
Ground Battery Under-voltage
Ⅳ. Description of Instrument Panel and Pushbutton Functions
1. Instrument model.
2. LCD display area.
3. Function button: Used to select various measurement functions.
3-1.SELECT: Key switch, used to select various measurement functions.
3-2. Manual range select switch, which is automatically identified when the device is powered on. Press "Select" key to enter automatic range mode. Press "Range" key for automatic/manual range switch. In manual range mode, press "Range" key once, it will skip to the previous shift. When it goes to the highest shift, it goes back to the lowest shift when the button is pressed again. The procedure repeats again in the same order. Press the key over 2 seconds, it will exit from manual range and enter the state of automatic range measurement.
3-3. It is automatic identification status when the device is powered on. Press "SELECT" to enter automatic measurement. MAX/MIN: the maximum value and minimum value. Press the function button and enter MAX mode, in which the maximum value is held; press the button again to enter MIN mode, in which the minimum value is held. After the MAX/MIN mode is entered, the display device indicates the current value. Press down MAX/MIN button for 2 seconds, and then exit from MAX or MIN test.
3-4. HOLD: Hold readings. Press the button to lock the displayed value, and press it again to unlock it.
4. Power switch
5. - Input insert chip: The negative terminal of capacitance measurement.
6. + Input insert chip: The positive terminal of capacitance measurement.
7. COM input port: Insert black test lead to negative input terminal.
8. Input port: Insert red meter to measure the positive input terminal of resistance, capacitance, diode as well as on-and-off test.
Ⅴ. Other Functions
Automatic power off: After the meter is stopped for 10 minutes, it will cut off power automatically (power off), and then enter the dormant (power off) state. The built-in buzzer will send out warning tone for 3 times in one minute before it powers off. After one minute, it will send out a long beep and enters the dormant (power off) state. If you want to restart power (power on), please press “SELECT”，“RANGE ”“MAX/MIN”，“HOLD” key or the power switch key. If you want to cancel automatic power-off, press “SELECT” at the same time when you press down the power switch, then automatic power-off will be cancelled after power on, and “APO” symbol will be also turned off.
Ⅵ. Features
1. General features
1-1. Display mode: LCD
1-2. Maximum display: 5999.3 5/6 display automatic polarity display and unit display.
1-3. Measurement mode: dual integration A/D conversion.
1-4. Conversion rate: About 3 time/s.
1-5. Over range: Display “OL”
1-6. Low voltage display: the symbol displayed.
1-7. Working temperature: ：0～40℃, relative humidity <80%
1-8. Storage temperature: -10～50℃, relative humidity <80%
1-9. Power: AAA 1.5v batteries (Two)
1-10. Volume (Dimensions): 185mm×91mm×49mm（Length*width *height）
1-11. Weight: About 408g (including battery)
2. Technical features.
2-1. Accuracy: ±（a% reading + d digits）, the ambient temperature for ensuring accuracy: 23±5℃, relative humidity <75%.
2-2. The warranty period of calibration is one year from ex-factory date.
VII. Resistance
1. Turn on power. The initial status is the automatic identification mode of resistance, diode, On-and-Off Test and capacitance. Respectively insert the red and black meter pens into the holes of " " and "COM".
2. Press "SELECT" key to enter automatic resistance measurement mode.
3. When measuring resistance in automatic identification mode, the keys such as “RANGE”、“MAX/MIN”、“HOLD” do not have controlling effect. When the measured resistance is over 1MΩ, please press "SELECT" key to select automatic resistance measurement mode. At this time, the “RANGE”. “MAX/MIN” “HOLD” keys have the controlling effect.
Caution:
a) When measuring the capacity, all the powers within the tested circuits must be disconnected and the capacitance shall be sufficiently discharged.
b) When measuring the resistance, any occurrence of voltage may lead to inaccurate readings, and if the 250V protection voltage is exceeded, it may damage the meter or threaten the safety of the user.
c) When the range of 600Ω is in use, first sort-circuit the meter pens and measure the resistance of the lead wires and then deduct it in the actual measurement.
Range Accuracy Resolution
600Ω ±(0.8%+5d) 0.1Ω
6kΩ ±(0.8%+4d) 1Ω
60kΩ 10Ω
600kΩ 100Ω
6MΩ 1kΩ
60MΩ ±(1.2%+10d) 10kΩ
Open circuit voltage: 600mV.
Overload protection: 250V DC or AC peak values.
VIII. Diode and On-and-Off Test
1. Turn on power. The initial status is the automatic identification mode of resistance, diode, On-and-Off Test and capacitance. Respectively insert the red and black meter pens into the holes of " " and "COM".
2. Press "SELECT" key for two times to enter On-and-Off Test mode.
3. Press "SELECT" key for three times to enter Diode Test mode. When measuring diode, please insert the red meter pen to the